> Hard Drive
> Trouble Migrating An IDE Drive To SATA Mobo
Trouble Migrating An IDE Drive To SATA Mobo
Make sure your backup media is ready if you try any last ditch efforts, because they likely won't work twice. Return to Diagnostic Chart Computer Repair | Power Supply | Video Card | Motherboard/CPU/RAM | Hard Drives | CD and DVD | Sound Card | Modems | Networks | Foner Books I think it will work without any problem, but keep us posted. asked 3 years ago viewed 2431 times active 3 years ago Blog The 2017 Stack Overflow Developer Survey is Now Live Linked 0 Computer boots in safemode but get BSoD in this contact form
There's a massive hack to get windows XP to run off an USB drive though. by R. Sorry, there was a problem flagging this post. This is an easy way to add an IDE drive to a motherboard with a single IDE motherboard socket. http://www.sevenforums.com/hardware-devices/134485-trouble-migrating-ide-drive-sata-mobo.html
How To Connect Ide Hard Drive To Sata Motherboard
You cannot mix the two on the same controller to my knowlege. Just set the SATA drive to IDE mode first, then use a good disk cloning program to copy the drive.This works as long as the SATA controller is on the chipset, The problem of reinstalling Windows on a SATA boot device still happens with XP, but almost the first message from Windows asks you to "press F6 to install a Raid controller".
When Windows boots it will take a LONG time to get all the updated drivers - but hey, it booted, right? By the way, what are the short pci express slots for? Source Code © 2007-2017, Adam Scheinberg, except where noted Reader comments are owned by the poster. Ide Hard Drive Jumper Settings Two hard drives are connected: a 1 TB SATA disk and a legacy 160 Gig IDE drive connected with Syba.
Puneet Ballabh 7 103 visningar 4:35 USB TO SATA IDE CONVERTER ADAPTER - Längd: 4:00. Ide And Sata Drives In Same Computer Return to Diagnostic Chart The diagnostic tree splits here between the newer SATA (Serial ATA) interface drives and the older PATA (Parallel ATA) interface drives. Just take whichever tools you need from the toolset to USB-connect your drive and power it. (The toolset does not include a drive enclosure, so you'll want to buy that separately internet Many transition motherboards manage PATA and SATA drives together just fine.
Another step you should perform to minimize the chance of blue-screening is to run sysprep while the HD is booted on the old computer. Use Ide Drive With Sata Motherboard What I mean to say is Windows sees all HDD's as either IDE or SCSI, and it'll see SATA drives as IDE most times. My question is, if I were to do this would I be able to boot from the SATA drive, or would I need to just reinstall my operating systems on the Since the "S" in SATA stands for serial, the specification actually describes a bit rate, 1.5 Gbits/s for SATA 1, 3.0 Gbits/s for SATA 2, and 6.0 Gbits/s for SATA 3,
Ide And Sata Drives In Same Computer
To pump more data than this through the bus would require RAID anyway. original site by nelchael_com / November 22, 2006 5:48 AM PST In reply to: Same problem here... __[ In English, resume/summary ]______________________I get a HD SATA and want turn it the Primary Boot How To Connect Ide Hard Drive To Sata Motherboard My new SATA drive shows up as SCSI and on my taskbar in the safely remove hardware spot. Sata And Ide Hard Drives Together But it only recognizes a floppy as the source for the SATA controller.
Andrew SME 65 422 visningar 5:02 Como instalar HD IDE em placa-mãe SATA - Längd: 4:29. weblink Du kan ändra inställningen nedan. If you`re really lucky, a Windows repair might work, but it could be the long shoot. Label "A" is the SATA power connector, "C" is the "legacy" or IDE power connector, and "B" is the SATA data or "signal" plug. Motherboard With Ide And Sata Ports
Logga in och gör din röst hörd. never had much problems on that. If the motherboard BIOS supports AHCI (Advanced Host Controller Interface) you should enable it, otherwise the SATA drive will end up emulating an IDE drive if it works. http://fireflybsd.com/hard-drive/laptop-no-longer-sees-2nd-sata-drive.html Some SSD drives are sold with a PCIe (PCI Express) interface, but configuring these as the boot drive can be tricky or impossible.
Here is my problem. How To Install Ide To Sata Converter The jumpers on both drives should be set to cable select (CS) if you aren't setting one as Master and the other as Slave. So you could take an old 386 drive from 1988 and plop it into your Pentium 4 from 2005, and it would work!
The connectors aren't soldered to the wires, the circuit is made mechanically with "V" shaped contacts forced through the plastic and digging into the conductors.
You can connect either one or two IDE drives to an IDE ribbon cable. My mb is an Asus M2n-sli board. Well here’s one way to fix it. How Many Hard Drives Can Be Connected To A Single Ide Cable You can see where the IDE data ribbon cable plugs in to connect it to the motherboard and where the Molex power plug goes.
Flag Permalink This was helpful (1) Collapse - I've had this config. COOL!!!!There you have it. This configuration works well and though the access speed is slower for the IDE drive, I've never noticed it. http://fireflybsd.com/hard-drive/all-drives-now-sata.html He doesn't need any controller drivers loaded to use the SATA drive in IDE mode, as the generic windows drivers will work.
but I guess it may exist for reasons such as this so you never know. OSNews My Account Profile Preferences Comments Submissions Friends & Fans OSNews Privacy Statement|Notice to Bulk Emailers © 1997-2017 OSNews Inc. CyberTech 184 784 visningar 2:02 How to connect SATA devices in a PATA (IDE) only PC system - Längd: 2:33. I tried to use the Seagate Disc Wizard software but it wouldn't clone from my USB drive, although it recognized both drives.
If you're just looking for faster boot time, a SATA 3 SSD may make more sense. I've had this setup running on my machine for the last 2 years (approx) and haven't had any problems.Windows manages the two hard drives separatly so you shouldn't have any problems.I Felipe Marin B. 7 399 visningar 8:50 Replace or upgrade IDE to SATA dvd Drive or Hard Drive - Längd: 21:29. I have Windows 2000 with an AMD 2800 chip and A7V8X mobo.
more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed I will keep you posted though... A CD writer and a blank CD or a thumb drive or a USB hard disk Your Windows 7 install disc if you already tried the system repair option, or the
© Copyright 2017 fireflybsd.com. All rights reserved.